Two months before the AUS PEV Nationals, Dylan Bell broke his arm and thought his chances of racing at all were 50/50. The board we built him had one gentle test ride before it went in the car. The day before the finals he cartwheeled it into the grass at full throttle.
He still finished second.
Three of us raced eSkate Pro at Coffs Harbour Kart Club, 21 to 23 August. Dylan was on a 4WD race prototype, Adrian Treimanis on his own Mach One S and Liam on a 2024 Mach One converted for the track. It was the first time we'd built boards purely for racing.
Late nights and one test ride.
Dylan's board started as a Mach One carbon deck and enclosure, and nearly everything else changed. 18S lithium polymer, four-wheel gear drive, lowered suspension and 162mm CST semi-slicks. Two RTS torque vectoring modules ran two ESCs, which RTS was never designed to do, so Liam rewired the accessory pins so both modules could talk to each other.
The electronics wouldn't fit inside, so we cut a hole in the deck and mounted them on top. None of it was waterproof.
It came together over a lot of late nights and honestly we weren't sure it would be ready. Liam got one gentle ride on the backstreets, then packed the car for the 16 hour drive north.

A backstreet near the hotel.
Dylan drove three days from Perth, had car troubles on the way and got in too late for testing. So his first ride on the prototype was that night on a bumpy backstreet near the hotel, with bindings we'd only just mounted.
It stuttered under power and threw faults. Could have been the motor calibration, the new link between the RTS modules or the experimental electronic diff lock. We didn't sort it that night.
Adrian had his own surprise. We'd fitted his Mach One S with a bigger ESC a month earlier, about 50% more power, but the full power only got unlocked in the hotel room with a last-minute firmware flash that unlocked the full 9kw. He took it outside expecting a small difference and it flipped him straight onto his backside.
Practice didn't go well.
Dylan's front wheels kept losing grip, the front hanger would wobble and he'd back off the throttle, which killed his launches. Liam spent practice with a laptop, cutting front motor power to about 30% and turning off the diff lock and the front torque vectoring, and checking bolts and gears between sessions.
By the end of day one Dylan felt that fifth to seventh place was the best he might be able to manage, and he even felt that he would be better off back on the standard Mach One that he won the AUS PEV season championship series with. He looked pretty flat.
Liam was having more fun. His Mach One was set up lower and softer than stock, and the R6 trucks turned into something else. RTS on the rear pulled him into corners so hard that a few times he got on the power too early, crossed the inside curb and nearly ended up on the grass.

Then Dylan crashed.
The day before the finals he was coming down a straight at full throttle when his remote trigger jammed, probably a small stone. He got it free near the end and braked for a second, then ran into the grass and cartwheeled several times, only just missing a tyre barrier. Liam heard the crowd go up and realised it was Dylan.
He was completely unscathed. The rims were packed with mud and grass, but the electronics on top of the deck were untouched.
And from there something changed. Since the broken arm Dylan had been wary of falling, and now that was gone. He rode much harder, Liam's adjustments to the board were working, the lap times dropped and Dylan qualified second. That night we could keep chasing setup changes or leave him alone. We left him be.
Finals day.
Race morning the track was soaked. The sun dried most of it but practice still ran through puddles and drizzle, and the open electronics kept working.
Adrian had been battling Tas Ventouras and Jeff Cameron all weekend and looked good for third until a crash in the last heat pushed him back on the grid. He raced the final flat out and finished fourth, on a rear-wheel drive street board against purpose-built 4WD race boards.
Liam made the pro class and finished eighth on stock 12S power, geared under 65km/h.
Dylan lined up second next to Morgan Brady on a dialed Stooge V6 with treated kart tyres. They were neck and neck off the start but Morgan edged away. He held off Jeff Cameron on a kart tyre Stooge V6 behind him. Dylan finished in 2nd place.

What we took home.
We went to Coffs to find problems with a new race board, not to win. Dylan took it to second on its debut weekend, in his first race since breaking his arm, after a crash that would have shaken the confidence of most riders. At last years nationals he took third in Perth on a Mach One. The real story is him.
We also learnt the R6 trucks set up low and soft feel nothing like a normal Mach One. Liam compares it to carving on a snowboard, and a few pros who tried it came back grinning.
You can't buy a race board yet, and you won't for a while. One good weekend doesn't prove a prototype is safe for anyone else. What we learn at the track goes back into the street boards, and the closest thing today is the Mach One S Adrian rode to fourth.
A special mention has to go to Lachlan Thaung for driving over from Perth with Dylan and racing for us on a 2024 Mach One, ending on the podium in novice class.
We also really want to thank the AUS PEV crew for the hard work they put in. The events always run smooth and professionally and provide a welcoming and positive atmosphere. They are doing the hard miles to grow the sport in Australia and we're very excited for the future they're building.
Full results are on the AUS PEV leaderboard.


0 comments